Harvi is a clever little device that enables the Zappi and Eddi products to be installed without using a directly wired current transformer (CT) for measuring the grid and or generation power; instead the CT is connected to Harvi.
No power source is needed for Harvi - the energy from the CT is harvested and used to transmit the measurement signal to the Zappi or Eddi. This means batteries or electrical wiring are eliminated!
Up to three devices can be monitored by the Harvi. You will need to buy a Zappi, Eddi or separate CT clamp for the Harvi to work. Not G100 compliant for Grid Monitoring, you'll need to hard wire if you require G100 compliance.
When installing, consider the positioning of the unit and avoid metal obstacles and range will be reduced by obstructions.
The Myenergi Hub adds wireless monitoring to your zappi and/or eddi system. Through the app you can seamlessly track the use of your surplus energy to power your car or heating.
The Hub also checks for and downloads the latest software updates from Myenergi, meaning that your system will be as up-to-date as possible and you can take full advantage of any new features.
Compliance with G100 Issue 2 Amendment 2 is only supported via Ethernet on the SolarEdge EV Charger, connected to the same router as the SolarEdge Inverter.
SolarEdges smart home EV chargers use available solar energy for EV charging, providing the convenience of quick charging from home with cleaner, cheaper, renewable energy. Connection: Type 2 socket (European-wide, universal socket)
Compliance with G100 Issue 2 Amendment 2 is only supported via Ethernet on the SolarEdge EV Charger, connected to the same router as the SolarEdge Inverter.
SolarEdges smart home EV chargers use available solar energy for EV charging, providing the convenience of quick charging from home with cleaner, cheaper, renewable energy. Connection: Type 2 socket (European-wide, universal socket)
The Eddi 2.1 diverts surplus power from your solar or wind turbine system – putting it to use to heat your water or rooms rather than exporting it to the grid.
Eddi is an energy management system for use with grid-tied PV or wind turbine systems. Excess energy from the microgeneration system is used to heat water or rooms rather than exporting it to the grid. Two heaters are supported (typically top and bottom immersion heaters).
A grid current sensor (supplied) simply clips around the incoming supply cable. This sensor is used to monitor excess power and the Eddi automatically adjusts the voltage to the heater load, thereby consuming the surplus power. Harvi, a self-powered wireless sensor is available separately.
An internal expansion interface provides a means to add and expansion module to enable various functions such as auto switching from day-time and night-time supply, heat pump interfacing for legionella control and temperature sensing. An optional ELS module allows the Eddi to be officially used for G100 compliant Export Limiting Schemes, avoiding expensive grid network reinforcement costs.
The Eddi utilises myenergi’s proprietary VariSineTM technology to ensure compliance with worldwide power grid standards.
Comes with Anti-tamper Kit required from 31/12/2022.
Zappi just got better! Integrated Wifi in the new V2.1 units now means that they are OLEV Smart compliant without the need for an additional hub.
The new V2 model is BS 7671 18th Edition ready and comes with integrated RCD and Earth fault detection. This eliminates the need to install an expensive Type B RCD or an earth electrode.
Zappi works like any regular charging point but has special eco charging modes which will benefit homeowners with grid-tied microgeneration systems.
The ECO+ charging mode will automatically adjust the charging rate to only make use of surplus power that would otherwise be exported from the property - which means that charging your car is effectively completely free!
The ECO mode is similar, but allows you to specify a minimum that should be put into the car by a particular time, in order to minimise use of imported power but still ensure you have sufficient charge to use the car.
In FAST charge mode, zappi operates like any ordinary EV charging station.
Zappi is a Mode 3 charging station, compatible with all electric vehicles that comply with SAE J1772, EN62955, EN62196 and EN61851 plug-in electric vehicle standards.
Please select the colour for your vehicle charger from the options dropdown - White or BlackThis charger has a Type 2 connector.
Zappi just got better! Integrated Wifi in the new V2.1 units now means that they are OLEV Smart compliant without the need for an additional hub.
The new V2 model is BS 7671 18th Edition ready and comes with integrated RCD and Earth fault detection. This eliminates the need to install an expensive Type B RCD or an earth electrode.
Zappi works like any regular charging point but has special eco charging modes which will benefit homeowners with grid-tied microgeneration systems.
The ECO+ charging mode will automatically adjust the charging rate to only make use of surplus power that would otherwise be exported from the property - which means that charging your car is effectively completely free!
The ECO mode is similar, but allows you to specify a minimum that should be put into the car by a particular time, in order to minimise use of imported power but still ensure you have sufficient charge to use the car.
In FAST charge mode, zappi operates like any ordinary EV charging station.
Zappi is a Mode 3 charging station, compatible with all electric vehicles that comply with SAE J1772, EN62955, EN62196 and EN61851 plug-in electric vehicle standards.
Please select the colour for your vehicle charger from the options dropdown - White or BlackThis charger has a Type 2 connector.
